The most vulnerable components in high-pressure blowers also include its impeller because it easily scratches the parts around it, causing damage. What causes the high-pressure blower impeller to be so troubled?
Since high-pressure fans will generate high temperatures when operating, operators should avoid touching the fan shell to avoid burns. There are many other things to note about high-pressure fans, and I hope you can fully grasp it.
During use, changes in air pressure will cause high-pressure fan motor load current to telephone, so when wiring it, you should choose a suitable overload protection switch and use it at a rated full load current to avoid the motor burning. At the same time, clean the inside and outside of the high-pressure fan regularly to maintain good heat dissipation effect and reduce the occurrence of faults.
If the high-pressure fan is running in a bad manner or abnormal noise occurs, the power supply needs to be turned off immediately for maintenance, otherwise it may cause damage to the parts. In addition, the surrounding environment has a great impact on the equipment. If the temperature rises, do not place the high-pressure fan in a sealed room.
* Common are the scratches between the impeller and the impeller, as well as the scratches between the impeller and the casing and wall panels. Once a high-pressure blower occurs, problems will occur to varying degrees. In the past situation, it may be because there are impurities on the impeller, which makes the gap between the impeller too small, and it only takes clear dirt to solve it. It may also be that the gears are not fixed or worn, and the impeller cannot be synchronized; it may also be that the bearing wear causes the gap to increase.
The reasons for the latter scraping situation are similar, either because the installation clearance is incorrect, or the operating pressure and temperature may not meet the requirements, or the deformation of the case or base of the high-pressure blower, resulting in the failure of the equipment positioning.
Since high-pressure fans will generate high temperatures when operating, operators should avoid touching the fan shell to avoid burns. There are many other things to note about high-pressure fans, and I hope you can fully grasp it.
During use, changes in air pressure will cause high-pressure fan motor load current to telephone, so when wiring it, you should choose a suitable overload protection switch and use it at a rated full load current to avoid the motor burning. At the same time, clean the inside and outside of the high-pressure fan regularly to maintain good heat dissipation effect and reduce the occurrence of faults.
If the high-pressure fan is running in a bad manner or abnormal noise occurs, the power supply needs to be turned off immediately for maintenance, otherwise it may cause damage to the parts. In addition, the surrounding environment has a great impact on the equipment. If the temperature rises, do not place the high-pressure fan in a sealed room.
* Common are the scratches between the impeller and the impeller, as well as the scratches between the impeller and the casing and wall panels. Once a high-pressure blower occurs, problems will occur to varying degrees. In the past situation, it may be because there are impurities on the impeller, which makes the gap between the impeller too small, and it only takes clear dirt to solve it. It may also be that the gears are not fixed or worn, and the impeller cannot be synchronized; it may also be that the bearing wear causes the gap to increase.
The reasons for the latter scraping situation are similar, either because the installation clearance is incorrect, or the operating pressure and temperature may not meet the requirements, or the deformation of the case or base of the high-pressure blower, resulting in the failure of the equipment positioning.
Elevator Guide Shoe
- elevator shoes,
- elevator guide shoe,
- elevator slipper guide shoes
- elevator door guide shoes /slide shoes
- Rated Speed≤2.5m/s
- Width of guide rails B1 10,16mm
product
- Elevator Guide Shoe , 16mm Width Of Guide Rails PB233
- Slipper Elevator Guide Shoe , Rated Speed≤2m/s
- Elevator Guide Shoe , Width Of Guide Rails B1 10 ,16mm PB229
- Slipper Elevator Guide Shoe For Elevator Door , PB231
- Car / Elevator Guide Shoe ,≤2m/s Rated Speed PB177K
- Slide Elevator Guide Shoe ,16mm Width Of Guide Rails PB234
Elevator Guide Shoe, Slide Elevator Guide Shoe, Slipper Elevator Guide Shoe
Ningbo Xinda Elevator Traction Technology Co., Ltd. , https://www.xinda-elevator.com