Serious management of dust hazards cannot be delayed

Serious management of dust hazards cannot be delayed

A few days ago, the State Administration of Safety Supervision issued a "Notice" requesting the strengthening of dust hazard management in cement manufacturing and stone processing companies. The "Notice" pointed out that it takes about one year for all regions to focus on special management. For cement manufacturing and stone processing enterprises that have failed to meet dust control requirements and have excessive dust concentrations by the end of May 2014, they shall be ordered to cease operations that generate dust hazards; for those that do not meet the requirements by the end of October 2014, they must submit a request to the local government. The government closed it according to law.

This is based on the inspection and inspection of 31 cement manufacturing companies and 20 stone processing companies in 6 provinces organized by the General Administration of Surveying and Testing Institutions from May to August 2013. In addition, the "Notice" also put forward corresponding governance measures on issues found in the investigation.

Gao Shimin, Director of the Department of Occupational Health of the State Administration of Safety Supervision, stated in an interview: “This survey found that the prevention and control of dust hazards in cement manufacturing and stone processing companies is not optimistic, and the concentration of dust in the workplaces inspected is generally excessive, especially for small and medium-sized micro enterprises. The management foundation is very weak, the effect of dust removal facilities is poor, personnel protection equipment is not in place, personnel have not been trained for training, dust-taking personnel have not carried out occupational health inspections and other problems are widespread. Some enterprises are still using the production technology that the country has explicitly eliminated, and the dust hazard is very high. Seriously, governance cannot be delayed.”

Different processes in the two industries are different, but the dust hazard is very serious

“Despite the fact that the process of the two industries is very different, dust hazards in the workplace are very serious and must be given enough attention.” Gao Shimin stressed that “not only is the dust concentration of small and medium-sized micro enterprises exceeding the standards, but also the dust concentration of some large enterprises has exceeded the standard, only in terms of degree. There is a difference. There is no dust concentration that exceeds the standard in the companies surveyed and tested."

Digital speaking is the most objective. From the inspection results, the total dust concentration in the packaging and loading positions of the cement manufacturing enterprises (hereinafter referred to as the total dust concentration) was between 4.07 mg/m3 and 462.73 mg/m3, exceeding the maximum of 115.68 times; the respiratory dust concentration (that is, can enter Dust in the lungs, hereinafter referred to as dust concentration, is between 2.64 mg/m3 and 115.53 mg/m3, with a maximum exceeding 77.02 times. The total dust concentration of cutting, grinding, and carving posts in stone processing enterprises is between 1.50mg/m3 and 852.00mg/m3, and the highest exceeds 852 times; the dust concentration is between 1.20mg/m3 and 124.33mg/m3, and the highest exceeds 177.61 times. .

In order to allow journalists to better understand these figures, Gao Shimin gave an example: “At the time of the investigation, the floor of a cement manufacturing company's packaging workshop was covered with thick dust. I accidentally stepped on and left a deep impression. Footprints almost drowned the entire foot. The dust concentration on the job site can be thought of, and how bad the environment is. Workers working in this environment can take a long time without occupational disease?"


This website solemnly declares: This article is the reprint of the online media, only represents the author's point of view, has nothing to do with this site. If news articles and comments infringe your legal rights, please call us and we will handle it in a timely manner.

Diamond Grinding Wheel

Our diamond grinding wheel comes in two types which are respectively applicable to the grinding industry of die and hard alloy, as well as glass industry.

This type normally adopts resinoid bond and is applied to the grinding industry of die and hard alloy. In order to offer unsurpassed quality, we have been always choosing top grade diamond and powder resins, and the core is available as aluminum type and Bakelite type.

Featuring extreme sharpness and high precision, our resin bonded diamond grinding wheel is ideal to process hard alloyed cutting tool, and can be applied to surface grinder and normal lathe. Furthermore, a wide range of shapes is also available, such as parallel type, cup and saucer types, from which numerous applications are also possible.

Cup Stone Grinding Wheel,Diamond Grinding Wheel,Resin Diamond Grinding Wheel,Angle Grinder Diamond Wheel

DANYANG HANFENG TOOLS CO.,LTD. , https://www.hanfengdiatools.com

This entry was posted in on